Universal hydraulic brakelight switch. This hydraulic switch replaces discontinued brake light switches by bolting in place of a double banjo bolt on the handlebar or rear brake master cylinder

Especially suitable for replacing the standard switch on models where the front brakes have been 'de-linked'

 1 in stock

Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 This part is due back in stock soon, call 01484 841395 to reserve yours

Sidestand cutout switch

See ELA81319 for rotary switch that was fitted to some models

 This part is available by special order, request a quote

 639542 MG639542

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

Oil temperature sensor

See ELA03330 for sensor support

 1 in stock

 29724961 GU29724961 29 72 49 61
 2972 4961 2972.4961 29.72.49.61

Spark plug cap

Also known as suppressor cap Guzzi ref 2D000005 and GU02717450. See ELA02450 for less expensive alternative

 This part is available by special order, request a quote

2D000247

Pair of key blanks

Also known as Guzzi ref. 32735511 You will need to give these blanks to a locksmith together with your existing key to get copies made

 This part is available by special order, request a quote

 32735510 GU32735510 32 73 55 10
 3273 5510 3273.5510 32.73.55.10

12 volt ignition coil for models equipped with points, Bosch or Motoplat ignition systems, includes HT lead. Terminal layout is different to original coils- see photos.

Not for Digiplex models. Also known as Guzzi ref. 19716500, 19716520

 2 in stock

 31716560 GU31716560 31 71 65 60
 3171 6560 3171.6560 31.71.65.60

Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.

 1 in stock

 01738800 GU01738800 01 73 88 00
 0173 8800 0173.8800 01.73.88.00

Prolong battery life with this 9 stage smart battery charger, suitable for 6v, 12v AGM and lead acid batteries.

Weatherproof - suitable for use outside 6V / 12V 1A Auto-sensing charger. Suits all AGM, Lead Acid, Calcium and Gel batteries Charges 6v and 12v batteries Ring terminal and alligator clip harnesses included Spark proof Maintains full charge Simple, connect and wait for green light Overload / Short circuit protection See ACA96001 for a spare set of charging leads (e.g. for a separate bike).

 This part is due back in stock soon, call 01484 841395 to reserve yours